Search
Submit
Close
language
中国
韩国
韩国
韩国
韩国
韩国

NEWS

Do you know the installation method of Low price glass door manufacturers?

  • Categories:glass door
  • Author:
  • Origin:
  • Time of issue:2021-06-09
  • Views:0

(Summary description)Low price glass door manufacturers are combined with fixed glass and movable Low price glass door manufacturers to locate the line. According to the requirements of design and construction drawings, release the positioning line of Low price glass door manufacturers and determine the position of the door frame.

Do you know the installation method of Low price glass door manufacturers?

(Summary description)Low price glass door manufacturers are combined with fixed glass and movable Low price glass door manufacturers to locate the line. According to the requirements of design and construction drawings, release the positioning line of Low price glass door manufacturers and determine the position of the door frame.

  • Categories:glass door
  • Author:
  • Origin:
  • Time of issue:2021-06-09
  • Views:0

Do you know the installation method of Low price glass door manufacturers? Let’s take a look at it with the editor below!
1. Positioning and setting-up
Low price glass door manufacturers are combined with fixed glass and movable Low price glass door manufacturers to locate the line. According to the requirements of design and construction drawings, release the positioning line of Low price glass door manufacturers and determine the position of the door frame.
2. Limit slot at the top of the installation frame
The width of the limit groove should be two to four millimeters greater than the thickness of the glass, and the depth of the groove should be ten to twenty millimeters. During installation, at the beginning, two metal decorative board edges are drawn from the center line of the bomb, and then the limit groove on the top of the door frame is installed according to the edge line, and the groove depth in the notch is adjusted through the glued backing plate.
3. Install wooden bottom brackets with metal finishes
Fix the square wood on the ground, and glue the metal veneer to the wood. If the aluminum alloy square tube is used, it can be fixed on the frame column with aluminum angles, or fixed on the wooden bricks buried in the ground with wood screws.
4. Install the vertical door frame
The square timber of the door frame is nailed to the center line of the bullet, and then the shape and position of the door frame column are determined with plywood, and then the metal decorative surface is covered. When decorating the bag, place the front seam of the decorating face at the middle door position on both sides of the installation glass.
5. Install glass
Use a glass suction cup machine to suck the thick glass tightly, and lift the thick glass plate to the installation position. First insert the upper part of the glass into the limit slot on the top of the door frame, and then put the lower part of the glass on the bottom support.
6. Fixed glass
Nail two small square wooden bars inside and outside on the bottom square wood to clamp the thick glass to the middle door, apply all-purpose glue on the square wood bars and glue the facing metal to the square wood bars.
7. Seal with glass glue
Inject glass glue into the gaps on both sides of the top limit slot and bottom bracket opening, as well as the gap between the thick glass and the frame column, and use a tool to scrape off the excess glass glue.
8. Glass docking
When the fixed part of Low price glass door manufacturers needs to be spliced ​​due to the large size, the seam must be two to three millimeters wide, and the glass plate edge must be chamfered.


9. Floor spring installation
Before the door leaf is installed, the floor spring and the positioning pin on the top surface of the door frame should be installed and coaxial. It is recommended to use a hanging vertical line to check to ensure that they are in the same straight line during installation.
10. Install upper and lower door clamps
Install the upper and lower metal door clamps on the upper and lower ends of the Low price glass door manufacturers respectively. If the height of the door leaf is not enough, you can ply the wooden plywood at the bottom of the glass in the lower door clamp.
11. Fixed door clamp
After setting the height of the door leaf, insert small wooden strips into the gap between the glass and the upper and lower door clamps, and pour glass glue into the gap to fix it.
12. Door leaf installation
First, use the adjusting screw to adjust the positioning pin out of the plane of the crossbeam by 2 mm, and erect the office Low price glass door manufacturers. The hole of the rotating pin connector in the door clamp under the door leaf is aligned with the rotating pin shaft of the floor spring, and then rotate. Set the hole position of the door leaf onto the pin shaft, turn the door leaf at right angles to the cross beam of the door frame, align the rotation connector hole in the upper door clip of the door leaf with the positioning pin on the cross beam of the door frame, adjust the adjustment screw of the positioning pin, and insert the positioning pin into the hole Inside.
13. Handle installation
Before installation, apply a little glass glue to the part where the handle is inserted into the glass. When the handle is assembled, the root is close to the glass and then tighten the fixing screws to ensure that the handle is not loose.

OWNIC
e-mail

E-mail

E-mail

TOP

Address:No.78 Jingyuan Road, High-tech Zone, Ningbo, China

Fax:86-574-88232569

Website:http://en.ownic.com.cn

Ziqi Mo
Email:
ziqimo.ownic@gmail.com

© 2020  Ningbo OWNIC Technology Co., Ltd  All rights reserved.   浙ICP备05031688号   Powered by www.300.cn 

智能分站

language
中国
韩国
韩国
韩国
韩国
韩国